• Potency: from 3 to 1000 KVA:

-Single phase: from 3 to 200 KVA.
-Three phases: from 10 to 1000 KVA.

• Voltages: 110V, 115V, 120V, 127V, 220V, 230V, 380V, 440V, 460V, 480V and others to order.
• Frequency : 60Hz and 50Hz + or - 5%.
• Input estabilization: + ou - 20%.
• Maximun output voltage variation : + ou - 1%.
• Estabilization coeficient ( input/output ) : 20.
• Do not introduce harmonic distortion.
• Time of total recuperation : 16,6ms - optional : 8,3ms
• Eficiency : Superior to 98%.
• Consumption in empty: Less than 0,2%.
• Power factor of the estabilizator: Bigger than 0,98.
• Eletronic Control System : By INTEL and MICROCHIP last generation microcontrollers - 33Mhz and 20Mhz with 68 pinos.
• Voltage monitor in TrueRMS value: Independent on the wave form, temperature variation from 0 to 60 ºC and frequency from 40 to 80 Hz.
• Regulation System: Indirect - by induction on the line by the "Buck-boost" transformer.
• Quantity of regulation curvs: 32 "tap changer" in linear form.

Obs.:There is a special model with 64 "tap changer" duplicanting the coeficient of estabilization.

• Regulation process: Totally static and independent in each phase.
• Over and under tension protection + missing phase: with programation of limits and times.
• Dotated with event memorization or event log: Exibit current and last events.
• RS 232 serial comunication for monitor and event log purposes.
• Soft start: When turning on, it rises up the voltage until the objective point in a gradative way.
• Do not turn on the output if the tension is not normal.
• Automatic recharge: Programmed in number of times and time for recharge.
• The same can be desactivated depending on the client needs. In this last case the charge enhancement is manual.
• By-Pass return tries: Programable in numbers of times and time. It can be habilitated or not. Once in protection mode, if the voltage come back to normal like programmed.
• Recharge tries by protection: After in protection mode if tension comes back to normal it returns to normal operation like programmed.
• Event warnings: Sonorous, illuminant and messages on the display.
• Board connections: Everything with quick connection.
• Control panel and command:

- Built in alfa-numeric keyboard with 16 buttons.
- Liquid cristal 4 lines display with 20 characters per line with backlight.
- Mechanic estabilizator's on/off switch in the built in keyboard.
- Mechanic charge's on/off switch with light indicator.
- Simultaneous exibit of 4 or more parameters and/or log events.

• Isolation with eletrostatic armour-plating (optional).
• Termomagnetic disjunctor in the input for protection against overload.
• Eletromagnetic contactor for output comutation and desarm in protection cases.
• Automatic and independent By-Pass on each phase with programable limits and times.
• Reduced dimensions.
• Programable output tension: + or - 10%.
• Acceptable overload: 10% during 1h: 100% during 15 Min and 500% during 1Sec
.
Obs.: This uppercharges for protection efects are programable up to 6 scales respectivelly in its percentuals and its times.

• Liquid cristal display with 4 lines with 20 characters per line with the exibit's fuctions:

- Simultaneous visualization of the 3 output tension of each phase ralating with the neuter ( R/N, S/N and T/N ).
- Simultaneous visualization of the 3 output tension of each phase ralating with the other ( R/S, R/T and S/T ).
- Simultaneous visualization of the 3 input tension of each phase relating to the neuter ( R/N, S/N and T/N ).
- Simultaneous visualization of the 3 input tension of each phase relating to the other ( R/S, R/T and S/T ).
- Simultaneous vizualization of the output tension, input tension, frequency and of the regulation mark of R's phase.
- Simultaneous vizualization of the output tension, input tension, frequency and of the regulation mark of S's phase.
- Simultaneous vizualization of the output tension, input tension, frequency and of the regulation mark of T's phase.
- Simultaneous vizualization of the 3 actual corrent in phases R, S and T.
- Simultaneous vizualization of the potency, serial number, fabrication date and model of the estabilizator.
- A menu that informs how to make the the by-pass manual, the return of the by-pass, turn on the charge, turn off the charge, enter in the ajust parameters by using a password and return to the normal mode.
- Reset to the stardards configurations.
- Occurred event and messages visualization. Ex.: Active By-Pass - phase S / lowertension / Reactivated.

Obs.:You can see this functions on the PANEL simulation session of the site by clicking on the alfa-numeric buttons. (Panel in Portuguese).